Videos on Team68

Las Vegas Motor Speedway - Outside Road Course CCW

Sun, 19 Apr 2026 00:00:00 +0000

1:46.4

Safety wired my turbo hardware and it finally stayed on. Car is feeling great, braking needs improvement still, maybe some-day I’ll learn to rev match? Probably not, just going to get drive by wire for auto-blip.

Current Alignment-ish (Could be different since xida install): Camber -2.4F -2.0R Caster 5.5* Toe 0F 1/8"R (toe-in)

Clips from 4/18-4/19 - How to pass under double yellow

Sat, 18 Apr 2026 00:00:00 +0000

Had the scariest experience I have ever had at a trackday yet. There was a black Camaro in my run group who completely ignored the yellow flags and waving double yellows, leading to him nearly rear-ending me. Thankfully I saw him coming and moved out of his way. I later overheard him complaining about how much traffic there was in this session… pretty wild.

Spring Mountain - Villeneuve

Sun, 01 Mar 2026 00:00:00 +0000

1:46.557

Welded the nuts to my turbo housing and they still came loose and blew the gasket…. Next solution on the list, safety wire.

Current Alignment-ish (Could be different since xida install): Camber -2.4F -2.0R Caster 5.5* Toe 0F 1/8"R (toe-in)

Ride Height: 104mm/100mm Front 116mm/110mm Rear 3.5* Rear wing angle

Spring Mountain - West (Corvette School)

Wed, 18 Feb 2026 00:00:00 +0000

1:18.51

Stage 8 hardware didn’t do the trick, inconel studs going in next. Already had a exhaust leak for this lap, didn’t do last session of the day.

Current Alignment-ish (Could be different since xida install): Camber -2.4F -2.0R Caster 5.5* Toe 0F 1/8"R (toe-in)

Las Vegas Motor Speedway - Outside Road Course CW

Sun, 30 Nov 2025 00:00:00 +0000

1:56.3

Really need to keep my turbo attached to the manifold. Day cut short with only 1 nut of 4 remaining on the turbo manifold studs. Going to try Flyin Miatas Stage 8 locking hardware.

Current Alignment-ish (Could be different since xida install): Camber -2.4F -2.0R Caster 5.5* Toe 0F 1/8"R (toe-in)

Buttonwillow CW13

Mon, 13 Oct 2025 00:00:00 +0000

1:59.272

Only did 2 sessions on this day, left a ton of time on the table. Turbo gasket keeps blowing after nuts back off.

Current Alignment: Camber -2.4F -2.0R Caster 5.5* Toe 0F 1/8"R (toe-in)

Mods: VVT swap - stock internals Kraken top mount manifold and 3" Exhaust GT2560R - 13psi Skunk2 TB - Ported VICS intake manifold ACT Streetlite flywheel - Supermiata 4-puck clutch disk and pressure plate FF640 injectors - DW200 Pump - E85 fuel FF R8 Coil on plug kit Flyin Miata coolant reroute 180* thermostat Supermiata crossflow radiator ms3pro 6 speed - 3.9 torsen 245/40/15 BFG Rival S 1.5 Supermiata Techna Coilovers 9kg/6kg Supermiata BX11 Front BBK - 2 Piece rotors GLOC r18 front pads r10 rears 9 Lives Racing 71" wing Singular Hood Vents